Identificador: 1248
Abierta
Descripción
PARTE # RT-R113 – TALADRO MULTIPLE - 13 TALADROS – VERTICAL – MANUAL
Nueva con garantía
Fotos y Características:
3/4 HP Spindle Drive Motor, TEFC
60″ Back Fence Assembly
(1) 13-Vertical Gear Driven Spindle Rows
10mm Bored Collets
(7) Right Hand, (6) Left Hand
(2) Index Pins
20″ X 48″ Work Table Surface
Wired 1-Phase 120 Volt, 60 Hz.
Manually Actuated Boring Cycle
Tooling Not Included
Crated Dimensions: 45″ X 80″ X 44″ and 508 Lbs
Designed and Manufactured in the USA
The starting point for our line boring machines, this unit is both affordable and built to last. No more using templates that wear out quickly and lose accuracy. This machine is easily adjustable for entry and exit points, and cleanly allows the user to repeat the drill hole pattern with centering pins on both the left and right hand side of the machine. The rear fence is adjustable for offset from the edge as well. If you’re looking for your first line bore drill, look no further. This machine will give you many years of service with little to no maintenance. This is a clear choice among professionals.
Pago y Devoluciones
- Forma de pago
- Visa/Mastercard/American Express
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
SOLDADORA DE MADERA - ALTA FRECUENCIA
PARTE: 2TE-0001 – SOLDADORA DE MADERA – ALTA FRECUENCIANuevo con garantíaFeatures:Weight150 lbsDimensions66 × 43 × 44 cmSupply240 volt / 50hz (standard 13-amp 3-pin plug)Generator frequencyNominal 27.2 MhzCuring speed3 – 10 seconds per weldPenetration50mm effectiveOutput0.5 – 0.6 amps at 2400 volts (internal HT) on loadFinishHardwearing powder coated finishElectrical SafetyCabinet and fittings are fully earthed. Cutout switch isolates main power if rear access panel is removed. 10 amp...
AMXmachinery
ENGOMADORA 1 LADO – 63” ANCHO - QUICK
PARTE: 12132
- ENGOMADORA 1 LADO – 63” ANCHO - QUICK
COMO NUEVA – NUNCA USADA
Width capacity: 63"
Maximum opening: 1-3/4"
Feed rate: 64 FPM (single speed)
8.27" diameter grooved acid and heat resistant SBR
rubber covered glue rolls
6.9" diameter hard rubber covered doctor rolls
Glue spread and material thickness are manually adjusted
made by turning chrome plated hand wheels
Aluminum drip pan catches clean up water
Powered by 2 HP motor
Includes roll guards...
AMXmachinery
CORTADORA ESQUINAS
PARTE: 2AC-CM40AIR - CORTADORA DE ESQUINAS - NEUMATICANueva con garantiaLa Cortadora Neumatica de Esquinas corta esquinas, agujeros y ranuras en placas, gafetes, señales y otros articulos. Estas unidades son para esquinas hasta de ½” de tamano, no es para los formatos grandes de ¾” y 1”. Se activa con un pedal de piso en cada corte, el poder de corte de la maquina se ajusta con el regulador de aire que viene en la prensa, incluye tambien un manometro, filtro y valvula de escape, pre...
AMXmachinery
GRABADORA DE MOLDURAS - MAKOR
PARTE: 12419 - PRENSA - GRABADORA DE MOLDURAS
- MAKOR
USADA – MUY BUENAS CONDICIONES
This
machine has been designed to hot-press directly on wood or using wood paste.
It
is particularly suitable for coffins and funeral fittings, furniture and
accessories, picture frames, pelmets, etc.
Press
length 17.71" to R/L
Material
max width; 7.68")
Engraving
depth 3mm
Dual
propane torch heaters
Includes:
Large inventory of wheels as shown
230 Voltage 60 Cycle 3 Phase
...