Identificador: 2589
Abierta
.PNG)
.PNG)
.PNG)
.PNG)
.PNG)
Descripción
TORNO 16'' X 60'' PARTE: 2GM-GML-1660HD
16” x 60”, 2-1/16” bore, 6 HP
- ISO 9001 certified
- Large spindle bore 2-1/16”
- Heavy Duty spindle D1-6
- One-piece solid cast iron machine base
- Heavy Duty guideway width 10-1/4”
- Heavy Duty main motor 6 HP
- 16 spindle speeds from 45-1,800 rpm, speeds: 45/70/90/108/140/165/215/255/330/385/510/585/770/900/1170/1800rpm
- 45 kinds of inch threads, and 39 kinds of metric threads
- Threading and feeding rate change without changing gears
- Spindle is balanced, hardened and precision ground
- Spindle is supported at 3-point by high precision bearings
- All gears and shafts are hardened and precision ground
- Guideways induction hardened and precision ground
- Automatic lubrication system in headstock and feed box
- SINO DRO (installed)
- Taper turning attachment (installed)
- 8” 3-jaw chuck with one set of reversible jaws
- 10” 4-jaw chuck
- 12” Face plate
- 5 1/2” large steady rest with roller jaws (bearings)
- Oil pump on Apron for all guideways and leadscrews
- 2” follow rest with roller jaws (bearings)
- Removeable gap
- 4-way tools post
- Foot brake
- Halogen Work light and coolant system
- Full length splash guard
- (2) dead centers and (1) reducing sleeve MT6/MT4
- Thread chasing dial
- Tool box and leveling pads
| Max. swing over bed | 16 1/16" |
| Max. length of workpiece | 60" |
| Max. swing over cross slide | 10 1/4" |
| Max. Swing in gap | 23 1/4" |
| Width of Bed | 10 1/4" |
| Effective length in gap to spindle | 8 1/2" |
| Effective length in gap to chuck jaws | 3 1/2" |
| Spindle bore | 2 1/16" D1-6 |
| Taper of spindle center | M.T. #6 (MT6/MT4 sleeve) |
| Spindle speeds | 45-1,800 rpm / 16 steps |
| Longitudinal feeds | 0.0018-0.07 IPR, 42 kinds |
| Cross feeds | 0.0009-0.03 IPR, 42 kinds |
| Inch threads | 70-2 TPI, 45 kinds |
| Metric threads | 0.2-14 mm , 39 kinds |
| Diametral Pitch threads | 8-40 DP , 21 kinds |
| Module threads | 0.3-3.6 mm, 18 kinds |
| Max. travel of top slide | 4 1/4" |
| Max. travel of cross slide | 8 1/2" |
Spindle length w/o chuck Leadscrew length X TPI | 20 1/2" 1 1/4" x 4 TPI |
| Diameter of tailstock quill | 2 1/16" |
Max. travel of tailstock quill | 5" |
| Taper of tailstock quill center | MT4 |
| Main motor | 6 HP, 220V/20A, 3 Phase |
| Coolant pump | 1/8 HP, 220V, 3 Phase |
Pago y Devoluciones
- Forma de pago
- N/A
Publicar mensaje
Ingresar to ask the seller a question.
-500x500.png)
AMXmachinery1
MESA CORRIENTE DESCENDENTE - 1 HP
MESA CORRIENTE DESCENDENTE - 1 HP * 2CL-FT2200Is ergonomic, energy efficient, and easy to maintain. Rubber anti-slip rings and removable location stops ensure the material does not move during the sanding process, and the dual filters safely trap sawdust particles. Rear suction boards and side deflector plates are removable for sanding larger surface materials. Is perfect for light to medium duty woodworking applications such as sanding and finishing.84” x 24” table surfacePerfect soluti...
-500x500.png)
AMXmachinery1
2GM-PRB - DOBLADORA DE TUBO HIDRAULICA 2''
PARTE: 2GM-PRB - DOBLADORA DE TUBO HIDRAULICA 2''3 HP Motor, rated at 220V, three phase. Gear driven manual positioning. 2” Dia. of roller shaft, 7-1/2” roller Dia.ISO 9001 certified2” schedule 40 pipe is the maximum bending capacity, 2.5” round tube 14 Ga. and 2” square tubeEasy to operate in two positions; vertically and horizontally on its backDRO - Digitally displays your exact position and ensures repeatabilityHeavy Duty 4HP AC main motor1 - Top forming roll (hydraulic driven)2 ...
AMXmachinery1
SIERRA MULTIPLE - 1 SIERRA - 15 PULGADAS
PARTE: 2CK-C14RSIs a single-blade ripsaw is geared towards the shop looking to increase efficiency in their ripping operations but cannot justify a multi-blade ripsaw. With its precision cast iron chain and track assembly, and extended pressure section, the C14RS can produce a glue joint finish ready for panel glue-up right out of the saw.Produces a guaranteed glue joint finish to 15′, which eliminates the need to joint the material after rippingPrecision straight line feeding for parallel a...
-500x500.png)
AMXmachinery1
ARMADORA DE PUERTAS
PARTE: 2RI-R300V - ARMADORA DE PUERTASIs designed for high and low volume production requirements. Is the largest version of our heavy duty cabinet door clamping tables. In this system the operator is freed from the task of managing individual bar or pipe clamps, and instead, uses pneumatic clamp cylinders to apply pressure to the glue line. Each cylinder is easily operated by a slide toggle, and the entire system is activated by a foot pedal. The vertical easel allows for fast and square assem...