Identificador: 2805
Abierta
.PNG)
.PNG)
Descripción
PARTE: 2SS-WBS3760101 - LIJADORA CALIBRADORA 37" - BANDA ANCHA - 1 LIJA
Our American Made Wide Belt Sander will improve your finishing time, decrease your hand sanding and increase your productivity. Available with either a 10 horsepower, single phase or a 15 horsepower, three phase motor these American made wide belt sanders are workhorses that will likely outlive you.
Main Motor Options
- 10 Hp, Single Phase (1~), 220 Volt
- 15 Hp, 3 Phase (3~) 208 Volt / 230 Volt
- 460 Volt, 3 Phase (3~), 15 Hp
Wide Belt Sanders solve the most tedious challenge that woodworkers face!, the 37X60 Wide Belt Sander is built to last, including the following as standard equipment on this machine.
Standard Equipment
- Photo electric belt tracking.
- 2 1/2″ removable platen.
- 2 height adjustment indicators.
- 5 emergency stops.
- 2 rubber-covered pinch rollers 1 1/2″ OD.
- Rubber-covered contact roller 4 1/4″ OD with 13/8″ drive bearing.
- 2 machined idler rollers 2 3/16″ OD with 3/4″ bearings.
- Conveyor table set on four 3/4″ acme-threaded jackscrews
- Pneumatic belt tensioning.
- 3 year warranty.
- 6″ internal dust chute.
- 3/4 Hp conveyor motor
Pago y Devoluciones
- Forma de pago
- N/A
Publicar mensaje
Ingresar to ask the seller a question.
-500x500.png)
AMXmachinery1
TALADRADORA 32 mm, 21 CABEZALES
TALADRADORA 32 mm, 21 CABEZALES PARTE: 2CK-JB21PIs designed to speed up your line drilling operations. It has a total of 21-spindles based on a 32mm centers. The spring-loaded index pin allows for accurate and convenient continuous line drilling operations. The precision rear aluminum fence with linear scale and (2) flip stops allow for precise and convenient setup. The complete back fence can be adjusted for various measurements from the edge of the panel to the holes. The precisio...
AMXmachinery1
LIJADORA EN SERIE
PARTE: 2LA-6000 - LIJADORA EN SERIEWill brush sand and/or wire brush parts with standard widths from 25 to 73 inches. It has 1 to 6 spindles which will accommodate sanding or wire brushes up to 14 inch diameter. It has a fixed height conveyor and accommodates parts up to 9 inches thick.fully customizable to suit shop needsdesigned with a small footprintideal for sanding long thick partsruggeddependable
AMXmachinery1
SIERRA OPTIMIZADORA - AUTOMATICA
PARTE: 2CK-CFS100 - SIERRA OPTIMIZADORA - AUTOMATICAIs the perfect upgrade from your manual cutoff saw with 3 to 5 times higher production output. It is designed to scan for defects in your material which are indicated by a florescent crayon mark. The saw will cut on the crayon mark allowing for fast defect removal. Equipped with several cutting modes like fixed, sequential, defect cutting modes the operator can select the program most suited to their needs. The powerful 10HP motor and 1...
-500x500.png)
AMXmachinery1
ENCHAPADORA DE CANTOS - AIRE CALIENTE
PARTE: 2SS-EZ 60HA - ENCHAPADORA DE CANTOS - AIRE CALIENTEOur hot air edgebander applies your preferred choice of preglued edgebanding. Reduce the amount of panels discarded due to unsatisfactory edge banding installation. It features electronic variable speed control, digital temperature control, electromagnetic end cutters, an accutrim edge trim system and more. The innovative design of this American-Made machine makes it easy to use and provides a very dependable edgebanding solution. This ma...