Identificador: 2458
Abierta
ID de articulo : # 2458 se ha agregado a su lista de deseos.
Descripción
PARTE: 12572 - PRENSA DE RADIO FRECUENCIA - OGDEN
USADA - BUENAS CONDICIONES
Curing area: 36” x 60” x 2” thick.
Clamping pressure is applied by multi-power (dual pistons on a common shaft) pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two (2) 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
PART: 1AM-1250-E - PALLET NOTCHER - DOUBLE HEAD - 9” LENGTH - HEAVY DUTY
PART: 1AM-1250-E - PALLET NOTCHER - DOUBLE HEAD
- 9”
LENGTH - HEAVY DUTY New with warranty – 6-month warranty on manufacturing defects on
mechanical parts only(2) Motors 10 HP, 220/440V, 3 phase - connected to 220V(2) On/Off Switch with magnetic startersMaximum notcher size 9” long x 2-1/2” height x 1-5/8” depthEach cutterhead with 4 HSS knives installed - New design
Products specifications are subject to change without notice
AMXmachinery
SIERRA CINTA CENTAURO 31"
PARTE # 1RU-CE-R800-3 - SIERRA CINTA CENTAURO 800MMDiametro de las volantes 800 mm Inclinacion de la mesa 15grados Fuerza del motor 15 H.P. 3 fasesPeso neto aproximado 700 Kgs. Altura maxima de la guia 400 mm. Distancia entre sierra y columna 780 mm Ancho maximo de sierra 80 mm. Largo maximo de sierra 5530 Velocidad de la banda de sierra 28.5 mts/segundo Altura de la mesa desde el piso 950 mm Dimensiones de la mesa 1060 x 800 mm.
AMXmachinery
PARTE: 12422 - PRENSA DE ENSAMBLE FINGER JOINT
PARTE:
12422 - PRENSA DE ENSAMBLE FINGER JOINT
USADA
- BUENAS CONDICIONESMarca
WeiliModelo
MHZ 1550ªPrensa
para ensamble de piezas largas Finger JointLas
piezas se introducen ya encoladas
Largo
útil de ensamble desde 50 cm hasta 5 mt
AMXmachinery
CORTADORA ESQUINAS
PARTE: 2AC-CM80 - CORTADORA DE ESQUINAS - USO RUDONuerva con garantiaLa cortadora de uso rudo, esta diseñada para cortar aluminio hasta .080 y plasticos flexibles hasta .250” y otros materiales de peso intermedio.La cortadora tiene una mesa 6” mas ancha y tiene mesa con topes y agujeros para poner guias, para cortes repetitivos.Unidades de Corte Disponibles: ·Round - 1/2", 3/4", 1", 1.5” ·Slot - 1/4" x 1/2" (para aluminio y plastico .063”) Capacidad de Corte: ...