Identificador: 1919
Abierta
Descripción
PARTE: 2LI-D - MEDIDOR DE HUMEDAD PARA MADERA – SIN PINS - LIGNOMAT – LIGNO-SCANNER D
Nuevo con garantía
Measuring | 5-60% dependent upon species setting* |
Display | 0.1% resolution for the entire range. |
Species | 71 wood group settings, or simply use specific gravity of the wood, between 0.3 and 1.0 (setting 30-100) |
Gypsum | N/A |
Reference | 0-99 for non-wood building materials |
Calibration | Stable calibration not affected by ambient temperature. Calibration is internally checked and automatically adjusted if necessary. |
Calibration Check | External calibration check block #TS is available to verify the calibration and functions of meter. |
Included | Pouch, one 9V battery, manual and laminated wood group chart. |
Size | Pocket-size 2″ x 5.5″x0.5″, Measuring pad 1 5/8″ x 2 5/8″ |
Weight | 8 ounces (200g), made out of high-impact plastic |
Warranty | All moisture meters have a 2 year warranty. Pins and battery are excluded. |
The measuring depth of a pinless meter is crucial. Moisture readings are too low, when the Scanner is placed on a work piece which is thinner than the measuring depth. Scanners never measure any deeper than the measuring depth.
The entire measuring pad has to be on a flat and smooth surface for accurate readings
*Species Corrections for Ligno-Scanners and Ligno-VersaTec correlate directly to the Specific Gravity. Example: For a specific gravity of 0.57 (0.57g/cm 3 )set species # 57. Specific Gravity for most wood species can be found on the Internet. We also include a Species Chart with recommended settings.
The Ligno-Scanners SDM and the Ligno-VersaTec have calibrations built-in for drywall and concrete and a reference scale for non-wood building materials.
Measuring range: 5-60% dependent upon Species. For hardwoods the Scanners read lower than 5%, for softwoods the Scanners start reading above 5%. Resolution of read-out: 0.1% Less accurate above Fiber Saturation Point at 30%.
Wood temperature correction is not necessary.
1 9-V Battery for 3000 Readings, Battery included
Size: 1/2″H x 2″L x 5″W (for Scanner LD width is 2 7/8″) Weight: 8 ozs
Comes in a Carry Pouch with Belt Loop.
Pago y Devoluciones
- Forma de pago
- PayPal
Envio
- Ubicación de elemento de riesgo
- 31627, Chihuahua, México
- Enviar a
- México
- Retiros
- no recoger
- Devoluciones aceptadas
- No
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
PARTE: 12213 – SIERRA CINTA – CON ALIMENTADOR – SCMI 900-SC
PARTE: 12213 – SIERRA CINTA – CON ALIMENTADOR – SCMI
900-SC
USADA – BUENAS CONDICIONES
220V, 3 FASES, 60 HZ POR CONFIRMAR: VOLANTES 36" DIAMETRO, MOTOR DE 9 HP
AMXmachinery
CALDERA - CLEAVER BROOKS - GAS - 300 HP
PARTE: 12363 - CALDERA - CLEAVER BROOKS - GAS - 300 HP
USADA - BUENAS CONDICIONES
CLEAVER BROOKS 300 HP
MFG: 1996This unit has already been
removed and is ready to load.High pressure steam, 150 PSI
Natural Gas
-500x500.jpg)
AMXmachinery
FINGER JOINT SEMIAUTOMATICO
PARTE # 32M-FJS-005 – SISTEMA FINGER JOINT – SEMIAUTOMATICOEscalable a AutomaticoIncluye:Trompo- Motor Finger 20 HP- Motor Escuadra 5 HP- Motor Mesa 2 HP- Motor Bomba Hidraulica 1/2 HP- Velocidad 3-4 veces/minEnsambladora- Area de trabajo 5000mm largo x 150mm ancho x 75mm alto- Motor Cortador 5 HP- Motor Alimentador 1/2 HP- Motor Bomba Hidraulica 5 HP- Capacidad/min 3-4 piezas/min
AMXmachinery
BRIQUETEADORA – MOTOR 7.5 HP – DIAMETRO 50 MM (1.96”)
PARTE: 2CA-BP-100 – BRIQUETEADORA –
MOTOR 7.5 HP – DIAMETRO 50 MM (1.96”)Use sawdust, wood, paper, grass, leaves, all kinds of chips to make the briquettes.• Cost saving management of waste material reduces the volume of waste to be handled or shipped.• Effectively helps with compliance of local regulations mandating reduction of solid waste.• Converts waste into a valuable heating source for colder climates.• Increases profitability by converting waste into a marketable produc...