Identificador: 266
Abierta
Descripción
PARTE: 2TE-0001 – SOLDADORA DE MADERA – ALTA FRECUENCIA
Nuevo con garantía
Features:
Weight | 150 lbs |
Dimensions | 66 × 43 × 44 cm |
Supply | 240 volt / 50hz (standard 13-amp 3-pin plug) |
Generator frequency | Nominal 27.2 Mhz |
Curing speed | 3 – 10 seconds per weld |
Penetration | 50mm effective |
Output | 0.5 – 0.6 amps at 2400 volts (internal HT) on load |
Finish | Hardwearing powder coated finish |
Electrical Safety | Cabinet and fittings are fully earthed. Cutout switch isolates main power if rear access panel is removed. 10 amp panel-mounted fuse for protection. |
Hand gun specification | Lightweight, easy to use hand gun. Incorporates on/off trigger, thumb-operated fine tuning control and R.F. power indicator meter. Supplied with 2 sets of electrodes. |
Servicing and maintainance | A comprehensive range of spares are available and can usually be delivered next day. Repairs can be carried out within 1 – 2 days. |
Warranty | All new machines are covered by a standard 12-month warranty from the date of purchase. |
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
PARTE: 12553 - SIERRA TRONZADORA - 5 HP - GRUTTER
PARTE: 12553 - SIERRA TRONZADORA - 5 HP - GRUTTERUSADA
- BUENAS CONDICIONES
AMXmachinery
PARTE: AMX-10078 - AFILADOR Y TRISCADOR PARA SIERRAS CINTAS - TIMBERY SHARP-N-SET
PARTE: AMX-10078 - AFILADOR Y TRISCADOR PARA SIERRAS CINTAS - TIMBERY SHARP-N-SET
COMO NUEVO - SIN USARPARA SIERRAS CINTAS DE 1" A 1-1/2" CON 7/8" DE ESPACIO ENTRE LOS DIENTES (TOOTH SPACING)VOLTAGE 115/230 VAC
FRECUENCY: 50 - 60 HZ
PHASE 1
FULL LOAD AMPS: 5.0 / 2.5 A
DIAGRAM # 5520-989MANUAL DEL USUARIO INCLUIDO
AMXmachinery
CALDERA - CLEAVER BROOKS - GAS - 300 HP
PARTE: 12363 - CALDERA - CLEAVER BROOKS - GAS - 300 HP
USADA - BUENAS CONDICIONES
CLEAVER BROOKS 300 HP
MFG: 1996This unit has already been
removed and is ready to load.High pressure steam, 150 PSI
Natural Gas
AMXmachinery
MOLDURADORA – 5 CABEZALES – WEINIG PROFIMAT 26
PARTE: 12106 – MOLDURADORA – 5 CABEZALES – WEINIG PROFIMAT 26Usada – Muy buenas condicionesWeinig Moulder and Grinder packageWorking capacity: 9-1/16” x 4-3/4”Spindles Configuration: B-R-L-T-T-BMotors: Bottom 10 HP, Right / Left 10 HP, Top 15 HP, Top 20 HP and Bottom 10 hp.Spindles: Dia. 1 1/2" with rotation at 6,000 RPM. Digiset readouts for left and top spindles. Readouts on chipbreaker and hold down. Weinig ATS -E for left and top radial positioning.Feed: Variable speed 4 HP with ...