Identificador: 1762
Abierta
ID de articulo : # 1762 se ha agregado a su lista de deseos.
Descripción
PARTE: 2CK-PS43DA
Heavy duty construction with upgraded horsepower for production use
- Dual sanding heads for increased productivity
- First sanding head is steel with superior calibration results while the second head is a combination unit with adjustable platen for calibration and finish sanding capabilities
- Accurate digital thickness control to 0.001” (0.026mm) resolution
- Micro sanding drum height adjustments with dial indicators
- Caliper thickness setting unit for fast setup to your workpiece
KEY ADVANTAGES
- Heavy duty welded steel frame with cast iron sanding head assemblies for vibration free sanding.
- Dual rubber covered pressure rollers on infeed and outfeed for consistent material hold down.
- High quality rubber conveyor with automatic pneumatic belt tracking
- Extended infeed bed with two table rollers
- Table is adjusted using four heavy duty jack screws driven by robust chain system.
- Automatic caliper thickness setting
- Electronic sanding belt tracking
- Pneumatic belt tensioning & quick release outboard support for fast belt changes
- Automatic disc brakes for the sanding heads allows for fast belt changeover
- Safety switches on all access doors.
- High quality Schneider electrical controls and Comozzi pneumatic valves
|
|
Inch |
Metric |
|
Abrasive belt size |
43” x 75” |
1092 x 1900 mm |
|
Main motor first head |
25 HP |
|
|
Main motor second head |
20 HP |
|
|
Feed motor |
3HP |
|
|
Table rise/fall motor |
½ HP |
|
|
Maximum sanding width |
42” |
1066 mm |
|
Minimum part length |
17.5” |
440 mm |
|
Minimum material thickness |
1/8” |
3 mm |
|
Maximum material thickness |
5.9” |
150 mm |
|
Feed speed: variable |
12 to 46 FPM |
3.6 to 14 m/min |
Pago y Devoluciones
- Forma de pago
- N/A
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery1
SIERRA MULTIPLE - 1 SIERRA - 12 PULGADAS
PARTE: 2CK-C12RSHIs a single-blade ripsaw geared towards the shop looking to increase efficiency in their ripping operations but can not justify a multi-blade ripsaw. With its precision cast iron chain and track assembly, and extended pressure section, the C12RSH can produce a glue joint finish ready for panel glue-up right out of the saw.Produces a guaranteed glue joint finish to 10′, which eliminates the need to joint the material after rippingPrecision straight line feeding for parallel and...
AMXmachinery1
MOLDURADORA – 5 CABEZALES – OMIL PLM 5
PARTE:
12351 - MOLDURADORA – 5 CABEZALES – OMIL PLM 5
USADA BUENAS CONDICIONESANCHO MAXIMO 160 MMALTO MAXIMO 90 MMLARGO MINIMO 200 MMCABEZALES 5500 RPM6 MOTORES POTENCIA TOTAL
45.5 HP
HECHA EN BRASIL
AMXmachinery1
ASTILLADORA - VERTICAL - 25 X 35 PULGADAS
PARTE: 2TA-WG-2535V - ASTILLADORA - VERTICAL - 25 X 35 PULGADASFeatures:A specially designed with the push ram, powerful crusher for different materials such as wood, MDF, particle board,plastic, rubber, corn cob, etc.Excellent wearing ability and impact-resistant for time & labor saving.Large busting capacity and easy feeding system.The shaft rest for the cutter head is constructed by round hollow with special angle to keep cooling for long hours' usageCutter head angle cutting design allow...
AMXmachinery1
TALADRO MULTIPLE - 21 TALADROS
PARTE: 2CK-JB21PIs designed to speed up your line drilling operations. It has a total of 21-spindles based on a 32mm centers. The spring-loaded index pin allows for accurate and convenient continuous line drilling operations. The precision rear aluminum fence with linear scale and (2) flip stops allow for precise and convenient setup. The complete back fence can be adjusted for various measurements from the edge of the panel to the holes. The precision boring head has interlocking steel ...