Identificador: 2590
Abierta
ID de articulo : # 2590 se ha agregado a su lista de deseos.
.PNG)
.PNG)
.PNG)
.PNG)
.PNG)
Descripción
TORNO 16'' X 40'' PARTE: 2GM-GML-1640HD
- ISO 9001 certified
- Large spindle bore 2-1/16”
- Heavy Duty spindle D1-6
- One-piece solid cast iron machine base
- Heavy Duty guideway width 10-1/4”
- Heavy Duty main motor 6 HP
- 16 spindle speeds from 45-1,800 rpm, speeds: 45/70/90/108/140/165/215/255/330/385/510/585/770/900/1170/1800rpm
- 45 kinds of inch threads, and 39 kinds of metric threads
- Threading and feeding rate change without changing gears
- Spindle is balanced, hardened and precision ground
- Spindle is supported at 3-point by high precision bearings
- All gears and shafts are hardened and precision ground
- Guideways induction hardened and precision ground
- Automatic lubrication system in headstock and feed box
- SINO DRO (installed)
- Taper turning attachment (installed)
- 8” 3-jaw chuck with one set of reversible jaws
- 10” 4-jaw chuck
- 12” Face plate
- 5 1/2” large steady rest with roller jaws (bearings)
- Oil pump on Apron for all guideways and leadscrews
- 2” follow rest with roller jaws (bearings)
- Removeable gap
- 4-way tools post
- Foot brake
- Halogen Work light and coolant system
- Full length splash guard
- (2) dead centers and (1) reducing sleeve MT6/MT4
- Thread chasing dial
- Tool box and leveling pads
Max. swing over bed | 16-1/16" |
Max. length of workpiece | 40" |
Max. swing over cross slide | 10-1/4" |
Max. Swing in gap | 23-1/4" |
Width of Bed | 10-1/4" |
Effective length in gap to spindle | 8-1/2" |
Effective length in gap to chuck jaws | 3-1/2" |
Spindle bore | 2-1/16" D1-6 |
Taper of spindle center | M.T. #6 (MT6/MT4 sleeve) |
Spindle speeds | 45-1,800 rpm / 16 steps |
Longitudinal feeds | 0.0018-0.07 IPR, 42 kinds |
Cross feeds | 0.0009-0.03 IPR, 42 kinds |
Inch threads | 70-2 TPI, 45 kinds |
Metric threads | 0.2-14 mm , 39 kinds |
Diametral Pitch threads | 8-40 DP , 21 kinds |
Module threads | 0.3-3.6 mm, 18 kinds |
Max. travel of top slide | 4-1/4" |
Max. travel of cross slide | 8-1/2" |
Spindle length w/o chuck Leadscrew length X TPI | 20-1/2" 1-1/4" x 4 TPI |
Diameter of tailstock quill | 2-1/16" |
Max. travel of tailstock quill | 5" |
Taper of tailstock quill center | MT4 |
Main motor:
Note: | 6 HP, 3 Phase, 20AMP Prewired: 220VAC
30AMP Breaker Needed ( 20A x 1.5 ) |
Coolant pump: | 1/8 HP, 220V, 3 Phase |
Oil for Headstock / Gear box / Apron | #30 weight machine oil Eg: Texaco regal R&O 100, 3 Gal. |
Net weight: | 4,150 lbs. |
Overall Dimensions (LxWxH): Shipping Dimensions: | 79" x 38" x 56" 80”x36”x70” |
Pago y Devoluciones
- Forma de pago
- N/A
Publicar mensaje
Ingresar to ask the seller a question.
-500x500.png)
AMXmachinery1
ESPIGADORA HORIZONTAL
PARTE: 2PI-OTF - ESPIGADORA HORIZONTALIt is designed to belt position the workpiece, bore a hole, then advance the workpiece to the correct location for the inserter, inject glue or water (for pre glued dowels), and fire the dowel into the hole. A part is placed into the work zone referencing the back fence and advancing the part onto the belt. The belt system allows constant part feeding into the machine.Elimination of complicated machine setupQuick, accurate assemblyGain production times on C...
AMXmachinery1
TALADRO MULTIPLE - 21 TALADROS
PARTE: 2CK-JB21PIs designed to speed up your line drilling operations. It has a total of 21-spindles based on a 32mm centers. The spring-loaded index pin allows for accurate and convenient continuous line drilling operations. The precision rear aluminum fence with linear scale and (2) flip stops allow for precise and convenient setup. The complete back fence can be adjusted for various measurements from the edge of the panel to the holes. The precision boring head has interlocking steel ...
AMXmachinery1
ENCHAPADORA DE CANTOS - 230V, 1-3 FASES
PARTE: 2CK-MX340MIs an entry level edgebander with the perfect blend of quality and affordability. With fine attention to detail and quality componentry the MX340M can output high quality edges on cabinet parts and more. This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. User friendly controls and adjustments allow for efficient changeovers of edge tape thicknesses between 0.4mm & 3mm.Compact design makes it the ideal edgebanding solution for small worksho...
-500x500.jpg)
AMXmachinery1
SIERRA ESCUADRADORA - 10 PIES
PARTE: 2CK-P305Is built for the budget conscious user that still wants precision and accuracy. The machine has a precision sliding table which runs on ball bearings and hardened steel guide strips. It is equipped with individual motors for the main saw blade (5 HP) and scoring blade (1 HP). The blade height and tilt is manually adjusted by means of individual handwheels. The angle of the blade is displayed by a linear scale for added operator convenience. The rip fence runs on a ro...